Question #1: 1. When purchasing a commercial grade item, the supplier must have documented evidence of dedication of the item.
Question #2: 2. The dedication process includes the following: Safety Classification of the Item, Technical Evaluation, Failure Mode and Effects Analysis, Identification of Critical Characteristics, and Acceptance Criteria and Methods
Question #3: 3. For verification of critical characteristics for acceptance, ANY ONE of the following 4 methods is acceptable to use: 1) Special Test and Inspection; 2) Commercial Grade Survey; 3) Source Verification; 4) Acceptable Supplier/Item Performance Record
Question #4: 4. Method 1 (Special Tests and Inspections) is employed for dedication of commercial grade items after receipt of the item.
Question #5: 5. When Method 2 (CGI Surveys) is employed for dedication of commercial grade items, the survey shall include the following: Perform Technical Evaluation, Selected Critical Characteristics and Acceptance Criteria, and Verification the supplier’s QA program meets ALL the requirements of NQA-1
Question #6: 6. The adequacy of the controls when CGI Method 3 (Source Verification) is employed for dedication of commercial grade items shall include the following as a minimum: Critical characteristics clearly identified with the acceptance criteria, M&TE controls are verified, Testing is performed by qualified personnel
Question #7: 7. Important design, material, and performance characteristics of a commercial grade item or service that, once verified, will provide reasonable assurance that the item or service will perform its intended safety function is called?
a. Critical Characteristics b. Basic component Original Characteristics c. Qualification Characteristics
Question #8: 8. An acceptance process performed in accordance with NQA-1 to provide reasonable assurance that a commercial grade item or service will successfully perform its intended safety function and, in this respect, is deemed equivalent to an item or services provided under the requirements of NQA-1 is called?
a. Qualification b. Analysis c. Dedication d. Engineering Evaluation
Question #9: 9. A structure, system, or component, or part thereof that affects its safety function, that was not designed and manufactured in accordance with the requirements of NQA-1, is called?
a. commercial grade item b. basic component
Question #10: 10. Which one of the following is NOT a Nuclear Industry Standard?
a. 10 CFR 50 Appendix B b. NQA-1 c. 10 CFR Part 21 d. ASTM B21.1
Question #11: 11. Safety related component is a structure, system or component that is relied upon to remain functional during and following design basis events to assure: 1. The integrity of the reactor coolant pressure boundary; 2. The capability to shut down the reactor and maintain it in a safe shutdown condition; or 3. The capability to prevent or mitigate the consequences of accidents which could result in potential offsite exposures comparable to the applicable guideline exposures set forth in § 50.34(a)(1) or § 100.11 of this chapter, as applicable.
Question #12: 12. An evaluation of an item’s credible failure mechanisms and their effect on system and/or component function is called?
a. Safety Function b. Failure Modes and Effects Analysis c. Design Characteristics
Question #13: 14. The following are considered as an item’s safety classification: Safety Related, Non-safety Related, Augmented Quality
Question #14: 15. NEI-1405A allows for acceptance of services from a laboratory with one of the following accreditation:
a. ISO - 9001 b. ISO 17025 c. IEEE 344 d. ASME Section III
Question #15: 16. Equivalency evaluation can be used as the sole basis to accept a commercial grade item for safety related use
Question #16: 17. Method 4 (Item/Supplier Performance Record) can be used as a justification for sampling during the dedication process.
Question #17: 18. The number of critical characteristics chosen for acceptance is based on:
a. Engineering judgment and evaluation of the failure modes of the items b. The complexity of the item c. The specified operating environment d. The determined safety function e. All of the above
Question #18: 19. Dedication is a process that provides absolute assurance that the item will perform its safety function when installed in safety related application.
Question #19: 20. When you identify a 10 CFR Part 21, you must report it to:
a) US Department of Transportation (DOT) b) US Nuclear Regulatory Commission (NRC) c) US Department of Energy (DOE) d) Santa Claus (Man in Red) e) All of the Above
Question #20: 13. When evaluating an item for dedication, it is NOT important to verify if it has any digital components.
You have successfully completed the exam! Congratulations!
Unfortunately you did not pass this examination. Please contact ProcessQM at (505) 975-2148 for assistance.
200 DP Road, Suite A, Los Alamos NM 87544
© Copyright 2016 ProcessQM LLC. All rights reserved.